Vivanco 2 IN 1 TVDVB UNIVERSAL REMOTE CONTROL Instrukcja Użytkownika Pobierz pdf

UR 2 Universal TV-DVB Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 1

(GB) Instructions

Inserting the batteries

Open the battery flap on the back of the remote

control, press the tongue lightly downwards,

then insert 2 alkaline AAA batteries. Check that

the polarity markings on the batteries and in the

battery compartment are correctly lined up

(+=+), then close the flap carefully. – Always

use undamaged batteries.

Adapting to TV or DVB Set Top Box (or

SAT/Cable)

In order to control your TV or DVB you must

adapt or set the remote control to it. There are

two ways of doing so: direct control code entry

or code search.

If your UR 2 does not understand you it blinks

twice and you can then repeat the entry. Each

understood entry is confirmed by button

blinking briefly.

Direct control code entry using the enclosed

list

Example: setting to control a Panasonic

television set:

1. The enclosed list gives, for example, the

Panasonic Code 153.

2. To prepare code entry, briefly press the

SET button, and then the TV-button, until the

Powerkey lamp (LED) lights constantly.

3. Then press the number buttons (e.g. 1 5

3) in sequence.

4. Once the numbers have been entered the

button lamp goes out and the remote control is

ready to control your appliance.

5. Finally, test the control code setting by

trying to control your television set. If it does

not work at all or not correctly try a different

code from the list or the code search (see

below).

Code search

If the brand of your appliance is not in the list or

none of the codes given fits, we recommend a

code search.

Manual code search

1. Switch on the appliance to be controlled.

Program is running.

2. To prepare the code search, briefly press

the SET button and then additionally the . TV

or DVB button, until the lamp (LED) lights

constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp (LED)

blinks.

5. Press the ON/OFF (appliance

on/off) button repeatedly, approx. every second,

until appliance, reacts. - If you notice the

reaction of your appliance too late and the next

code has already been emitted you can go back

by pressing SET and then ON/OFF again. If

your appliance has switched itself off you must

switch it back on again, e.g. on the appliance or

with the original remote control, to continue

searching. - When your appliance reacts you

can also try out other buttons without

interrupting the search. If some buttons do not

work properly, simply continue searching with

ON/OFF .

6. When your appliance reacts correctly,

press the appliance button e.g. TV and end the

search. The lamp (LED) goes out.

- The search stops after approx. 30 seconds of

inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be controlled

so that you can watch a TV program.

2. To start the code search, press the SET

button, and then additionally the appliance

button TV or DVB , for more than 3 seconds

until the Power-key lamp (LED) starts to blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every 2

seconds.

4. When your appliance reacts, press any

button, except SET, to end the search. – If you

ended the search too late, continue to search

using the Manual Code Search (see above).

5. Finally, test the control code setting by

trying to control your appliance. If it does not

work correctly, please try the code search

again. The code search then begins with the

next code in the sequence. - Remember to

switch your appliance back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance whose code you want to read off, e.g.

TV.

2. Press the SET button and additionally 1,2

or 3, depending on the part of the code you

want to read off. For example, if you press

SET+1 and the code 153 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after SET+2 is released, e.g. it blinks

1 2 3 4 5 6 ... 16 17

Podsumowanie treści

Strona 1

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 1 (GB) Instructions Inserti

Strona 2

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 10 Automatyczne wyszukiwanie

Strona 3

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 11 4. Após a introdução dos

Strona 4

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 12 e porque os símbolos

Strona 5

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 13 Kodeidentifikation Du kan

Strona 6

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 14 6. Om din apparat rea

Strona 7

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 15 4. ,  )- 

Strona 8

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 16 / ( 

Strona 9

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 17 alespo< po dobu 3

Strona 10

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 2 5 times for the 5 in

Strona 11

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 3 2. Zum Start der Kodesuch

Strona 12

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 4 sur la liste ou qu&apo

Strona 13

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 5 Non pour appareils travail

Strona 14

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 6 4. Quando l’apparecchio

Strona 15

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 7 Búsqueda de código manual

Strona 16

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 8 plaats 2 alkaline AAA-b

Strona 17

UR 2 Universal TV-DVB Controller Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 9 weergegeven, bijv knippe

Komentarze do niniejszej Instrukcji

Brak uwag

Vivanco 2 IN 1 TVDVB UNIVERSAL REMOTE CONTROL Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Switche sieciowe Vivanco 2 IN 1 TVDVB UNIVERSAL REMOTE CONTROL. UR 2 Universal TV Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Switche sieciowe Vivanco 2 IN 1 TVDVB UNIVERSAL REMOTE CONTROL